Texas Instruments 74LS Logic Comparators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . December INTEGRATED CIRCUITS. 74HC/HCT 8-bit magnitude comparator. For a complete data sheet, please also download. Part Number: 74LS, Maunfacturer: National Semiconductor, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor.

Author: Nigami Faera
Country: Pakistan
Language: English (Spanish)
Genre: Literature
Published (Last): 15 January 2012
Pages: 13
PDF File Size: 10.23 Mb
ePub File Size: 17.70 Mb
ISBN: 922-3-92803-385-5
Downloads: 25199
Price: Free* [*Free Regsitration Required]
Uploader: Zulkidal

I don’t do well with word descriptions of circuits–can you draw a schematic?

A way to avoid that would be to de-glitch the circuit by adding a synchronizing flip-flop running at 16MHz just before the latching flip-flop. I’m currently designing the power-on-jump circuit datasheett my processor board.

You can’t use it while the inputs are changing. I’ve never had to use one. Glitchy output shouldn’t be a problem — glitch, I see how you got your nickname. Just to scratch my own curious itch, what does the connect to?

Hi No it won’t. Any decoder, like the will create big nasty full swing glitches that can only be removed with the proper clocked gating or latching.

74LS IC 8-BIT IDENTITY COMPARATOR — Majju

If you expect to use it, you need to turn the datasheeh off during the time when the compare inputs are in transition. I’m not that good with circuit design, but is it possible a monostable multivibrator one-shot would do datasgeet job?

  GENERATIVE CAPP SYSTEM PDF

This might cause a false trigger if your address trap was at B. For example, going from 9 to A might give a false compare of B for a few nanoseconds.

Hi I doubt you’ll be able to run the output of the directly to a datashset. I got lost reading that. When the system comes up from a reset, a 74LS with its inputs all tied to ground is connected to the data lines of the CPU and the data bus tranceivers are switched off — this feeds the CPU NOPs until the address equals what’s set on the DIP switch.

Sierra IC Inc

In other words, what function does it serve? It might work, but I don’t like it much. You could then use it as a clock. My calculations say yes, with lots of time datasyeet spare, but I’d like others’ opinions. Here’s the pieces relevant to Power on Jump: As the address lines transition and settle out, they might very well set up a glitch that agrees with the test condition, well before you intended.

Glitchy output shouldn’t be a problem — it needs to be inverted for the D-type flip 74,s688 clock anyway, so I’m using a 74LS14 inverter, which has Schmitt inputs and should clean up the signal into a nice, sharp positive-going square wave. Note that this would take away 62 nS from the access time of the first instruction fetch after the proper address compare, but it should be OK if you are using newer memory devices.

  DIONISIO AREOPAGITA OBRAS COMPLETAS PDF

It’s an 8-bit comparator, but it’s cheaper than the 74LS85 and has an enable input. There may be better ways to do this job so keep tinkering. I’m not talking about little tiny noise spikes.

It’s comparing the high four address bits to a 4-position DIP switch. This sets the D-type flip flop, which switches off the NOP generator datssheet turns on the bus tranceivers. You’re depending too much on the propagation delay of the 74 and the creating a clock pulse of the minimum required width t wclk on your datasheet. It is a glitchy signal.

It may even make it worse. This would also add about 62 nS to your latch clock which right now is only 3 gate delays long and would be difficult to see on an old low bandwidth scope. This is all fine.