ASTM D SURFACE ABRASION. This test method describes a procedure for estimating the resistance of transparent plastics to one kind of surface. the ASTM D abrasion resistant test by showing less than. 5% scattered light and haze after being abraded. 3M Construction Markets. ASTM D Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion. This test method describes a procedure for estimating the.
|Published (Last):||19 October 2012|
|PDF File Size:||2.70 Mb|
|ePub File Size:||7.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
This Regulation applies to safety glazing and glazing materials intended for installation as windscreens or other panes, or as partitioning, on power-driven vehicles and their trailers.
This European Standard specifies a method of determining abrasion resistance of automotive leather. This commercial item description covers the requirements for a structural fireman’s coverall to be used d1044 Navy damage control fire fighters.
Through our network of over adtm, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world. This tester applied to do the test of wear-resistant in skin, leather, cloth, paint, paper, flooring, plywood, glass and natural rubber.
Note 3 — Prior attempts to employ the Taber Abraser for volume loss determinations of various plastics 2 have been unsuccessful because of excessively large coefficients of variation attributed to the data. EN Resilient floor coverings – Determination of wear resistance aatm Part 2: This standard specifies the functional requirements and test methods for domestic kitchen sinks, used in residential domestic houses, guest houses and similar premises.
These practices cover the selection and use of procedures for astmm polymeric powders and powder coatings. BS EN Surfaces for sports areas – Determination of resistance to abrasion of non-filled synthetic turf This document describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions. MIL-DTLF Military Specification – Plates, Tags, and Bands for Identification of Equipment This specification covers the materials and physical characteristics of plates, tags and bands identification devices used for identification of equipment.
ASTM-D1044 Taber Abrasion Test Equipment For Suitcases / Carpets / Furniture
This specification covers powder coatings for interior steel, aluminum, copper-nickle and bronze equipment, furniture, and electrical box surfaces and on exterior steel, astk, copper-nickel, and bronze surfaces exposed to marine atmosphere, high humidity, seawater and weathering. The purpose of this test is to provide a general means to produce controlled abrasion on a card surface.
This Standard sets out a method for determining the abrasion resistance of atm paint coating or other finishes, such as anodizing, electroplating, paper products, rubbers, plastics, textiles, glass and concrete.
EN Wood-based panels-Melamine faced boards for interior uses-Test Methods This test measures the ability of the astmm surface of melamine surfaces boards to resist abrasive wear-through by rotating a specimen in contact with cylindrical wheels covered with abrasive paper.
This specification ashm adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external equipment identification or instruction see 6. This test method covers the determination of the abrasion resistance of leather using the rotary platform, double-head tester RPDH.
Note 1-Recent attempts to employ the Taber Abraser for volume loss determinations of various plastics, like earlier ones, have been unsuccessful because of excessively large coefficients of variation attributed to the v1044.
The test methods aetm are listed in Table 1. The number of revolutions of the specimen required to cause a defined degrees of abrasion is used as measures of resistance to abrasion.
This standard does not specify aesthetic and dimensional requirements. This method is intended for determining the abrasion resistance of cloths in terms of percent change in breaking strength, or breaking strength after a given period of abrasion, or the number of abrasion cycles required to produce a specified state of destruction.
Applicable industry It is used in testing the performance of leather products, such as suitcases, carpets, cardboard, clothing, glass, plastic coating, ceramic tile, metal plating, paints, varnishes, decorative sheets, high-pressure sheets, plastics, textiles, flexible floor mats, traffic paint, anodizing layer, blankets, electronic components, decorative plates, wax, label, leather, dental materials, car ornaments, resin, furniture, and scientific research laboratories; Commodity inspection, arbitration, and technical supervision departments, The formula is abrasive index formula: Polymer modified cementitious leveling screeds and wearing screeds.
ASTM D – 13 – Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion
CID A-A Gear, Fire Protective This commercial item description covers the requirements for a structural fireman’s coverall to be used by Navy damage control fire fighters. Surfaces for sports areas – Determination of resistance to abrasion of non-filled synthetic turf. AC KV Iron mesh: This Appendix specifies a method of measuring the ability of the surfaces of decorative laminated sheets to maintain their original design or colour under abrasive wear.
It is the purpose of this test method to provide a means of estimating the resistance of such materials to this type and degree of abrasion.
Determination of Properties The test measures the ability of the decorative surface of the sheet under test to resist abrasive wear-through to the sub-layer.
ASTM D – 99 Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion
Vitreous and Porcelain Enamels – Enamel coatings applied to steel for writing surfaces- Specifications. This method specifies the testing methods for determination of abrasion resistance of rubber, vulcanized asym thermoplastic hereafter referred to as “vulcanized rubber”. ISO Annex C Effects of Surface Finish and Colour on Scratch Resistance The test measures the ability of a decorative surface of the sheet under test to resist abrasive wear through to the awtm.
The entrance surface of the disc should have sufficient scratch resistance, which may be improved by a protective coating.
The purpose of this test is to determine whether safety glass has a certain minimum resistance to abrasion. This test method describes a procedure for estimating the resistance of Transparent Plastics to Surface Abrasion.
It shall be used when specified on the Engineering drawing. The abrasion resistance coating test shall be conducted in accordance with MIL-C Laminate floor coverings – Elements with a surface layer based on amnioplastic thermosetting resins – Specifications, requirements and test methods. This SAE recommended practice covers the requirements for rubber floor mats made from five types of rubber compound as required by the physical property requirements of the application.
The purpose of this test is to determine the extent of magnetic stripe abrasion resistance. This specification covers the materials and physical characteristics of plates, tags and bands identification devices used for identification of equipment. The purpose of this test is to determine whether the plastic has a certain minimum resistance to abrasion.
IOS-TM Surface Resistance-Test Methods Description of a method that measures the ability of a coated surface to resist abrasive wear-through to the underlying substrate by assessing the resistance to liquid paraffin fat in the abraded area. This International Standard specifies requirements for hard anodic oxidation coatings on aluminum and its alloys, including test methods. SAE J 80 Automotive Rubber Mats This SAE recommended practice covers the requirements for rubber floor mats made from five types of rubber compound as required by the physical property requirements of the application.
Therefore, it is advisable to refer to that material specification before using this test method. This specification covers the requirements for photosensitive anodized aluminum sheets and foils. Inspection Validating the specifications, value and safety of your raw materials, products and assets.
This test method covers the determination of the loss of pile, specifically pile pull out, due to abrasion. It can be used to determine the wear resistance of surfaces against abrasion and particularly for ranking different wear layer types within one type of product.