ISO Method of extraction of contaminants by agitation. ISO Method of extraction of contaminants by pressure rinsing. Find the most up-to-date version of ISO at Engineering This British Standard was published by BSI. It is the UK implementation of. ISO The UK participation in its preparation was.
|Published (Last):||23 May 2009|
|PDF File Size:||6.42 Mb|
|ePub File Size:||7.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
The cleanliness level of a component, as determined according to this method, depends to a large extent on the test parameters e.
In response to orders for international standards, it is BSI policy to supply the BSI iiso of those that have been published as British Standards, unless otherwise requested. Standards are also available from the BSI website at http: International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. To ensure process consistency, a blank test should be performed at regular intervals using identical test parameters.
It does not, therefore, cover appearance defects or contamination by liquid or gaseous materials.
BS-ISOMethod of extraction of contaminants by pressure rinsing_百度文库
NOTE The sizes specified in the inspection document for the blank should be as close as possible to the maximum particle size acceptable for the component and chosen to allow counting significant numbers of particles. Carefully rinse the collection equipment and collect all of the accumulated particles in a clean sampling container. These International Standards have been extended, modified and new ones have been developed to produce a comprehensive suite of International Standards to measure and report the cleanliness levels of parts and components fitted to automotive fluid circuits.
For example, if the component is of large size like a tankclean only those external surfaces which might contribute to contamination during the extraction process. Depending on the presumed amount of particles or extraction liquid volume, collect the extraction liquid in either a single or several sampling containers or, if appropriate, by using the vacuum suction system. The collection equipment shall be cleaned to achieve the requirement of 6.
In this case, the initial contamination level may be altered. This is size class G according to ISO The main task of technical committees is to prepare International Standards. Express the results of the cleanliness measurement according to ISO Always use suitable protective equipment.
Method of extraction of contaminants by ultrasonic techniques Part 5: This container shall be appropriate to the shape of the component and made of material compatible with the test liquid. Method of extraction of contaminants by pressure rinsing. For the particle count, this is applicable to the total number of particles larger than the smallest particle size specified in the inspection document.
Various BSI electronic information services are also available which give details on all its products and services. Find Similar Items This product falls into the following categories.
Next lower size class is F.
Main sources of blank contamination are: Production, Cleaning, Contaminants, Particulate materials, Road vehicles, Particle size measurement, Road vehicle components, Extraction methods of analysis, Engine components, Contamination, Internal combustion engines, Particle size distribution, Fluids.
Consequently, ISO requires the analysis of the total volume of extraction liquid and of all contaminants collected using an approved extraction method. The initial blank shall exhibit values stated in 6. For example, by performing a cleanliness analysis of a defined volume of liquid after the cleaning procedure of the set-up, it can be determined whether the inspection environment is in suitable conditions and acceptable for carrying out a validation procedure.
Method of extraction of contaminants by ultrasonic techniques ISORoad vehicles — Cleanliness of components of fluid circuits — Part 5: Learn more about the cookies we use and how to change your settings. Blank value General The acceptable blank value depends on the component’s presumed or specified cleanliness level and, depending on the analysis method, is as follows.
NOTE Any operation of dismantling might generate particles which could be added to or lost from the original amount of particles. NOTE 2 Instead of collecting in a container, the liquid samples may also be directed through a membrane filter directly connected to the outlet of the collection equipment.
Cleanliness of components of fluid circuits Vocabulary. The extraction conditions should be agreed upon between parties and included in the inspection document.
ISO shall not be held responsible for identifying any or all such patent rights. Copyright Copyright subsists in all BSI ixo. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.
BS ISO 16232-3:2007
The dispenser can also be used to rinse the test equipment and all other items. All parameters should be included in the cleanliness specification and in the inspection document and should be rigorously followed by the test staff. In order to achieve reliable performance of components and systems, control over the amount of particles introduced during the build phase is necessary, and measurement of particulate contaminants is the basis of control. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.
The ISO series has been drafted to fulfil the requirements of the automotive industry, since the function and performance of modern automotive fluid components and systems are sensitive to the presence of a single or a few critically sized particles. Particle mass determination by gravimetric analysis Part 7: The faster, easier way to work with standards.